fabrikant van led-aluminiumprofielen


LED-VERLICHTING

Aangepaste LED-achtergrondverlichting: bouw een systeem vanaf nul (gids 2026)

Backlit onyx feature wall illuminated by an LED sheet backlighting system
A backlit onyx wall: the sheet sits behind the stone, so the whole face glows instead of showing a row of LEDs.

A custom LED sheet backlighting system is how you light a surface, not a line. Instead of a strip inside a channel, you place a flat, cuttable sheet of LEDs behind onyx, marble, acrylic, fabric or a graphic diffuser, and the front material glows evenly from edge to edge.

This guide walks through the whole build in the order that actually matters on site: define the effect, measure the cavity, choose the sheet format, count the sheets, size the driver, wire and mount, then test before anything is closed up. It also covers the two things that decide whether the result looks expensive or amateur — light mixing distance En power distribution — plus a fault table for the uneven panels you have probably already seen.

What Is an LED Sheet Backlighting System?

An LED sheet is a flexible printed circuit board carrying a dense array of chips — typically 100 to several thousand per sheet — with a cuttable grid and connectors along the edge. Because the chips are spread over the whole area rather than packed into one line, the sheet produces a broad light field that a diffuser can blend into a uniform surface.

Flexible LED sheet panel with addressable LED array
A flexible LED sheet: a dense chip array on a thin PCB, cuttable on the grid and connected at the edges.

Three properties make it the right tool for backlighting: it is thin (often 1–3 mm, so it fits shallow cavities), it is cuttable on marked lines so it can follow corners and cut-outs, and it is modular — sheets daisy-chain so one driver can feed a large surface.

01

Area, not line

Designed to cover a surface. A strip lights an edge; a sheet lights the whole face behind a translucent material.

02

Cut on the grid

Most sheets are cuttable in 1-light, 3-light or 6-light modules, so irregular stone, L-shapes and corners can be covered without oversized gaps.

03

Thin enough to hide

A 1–3 mm sheet plus a 2–5 mm diffuser fits cavities that a strip-and-channel build could never squeeze into.

If your project is linear rather than areal — cove lighting, under-cabinet runs, skirting or a ceiling trench — a strip in a profile is cheaper and easier. Start with our complete LED-strip lichtgeleider, or go straight to under-cabinet LED lighting if that is the job.

Step 1 — Define the Application and the Effect

Before sheet size or wattage, answer one question: what must the surface look like when it is switched on? The answer decides density, diffuser grade and colour temperature far more than the budget does.

A

Functional light

Menu boards, lightboxes and work surfaces. Priority: lumen output and measurable uniformity, not mood.

B

Decoratieve gloed

Feature walls, headboards, bar fronts. Priority: soft, continuous light with no visible chips and no bright frame lines.

C

Beide

Retail displays and hotel lobbies, where the surface must glow and also read as lit. Balance brightness against diffusion.

Use this table as a starting point, then confirm with a physical sample — the front material changes everything.

ApplicationTypical cavity depthFormat that usually works
Backlit onyx / marble feature wall30 – 80 mmModular sheets in a grid, or cut-to-shape around veining
Kitchen island / bar counter40 – 90 mmModular 480 × 240 mm grid or long-roll runs
Lightbox / menu board / signage60 – 120 mmLong-roll, high density, single continuous run per band
Display cabinet, shelf, niche20 – 40 mmSmall modular sheets or narrow cut sections
Headboard / fabric panel20 – 50 mmModular sheet, warm CCT, low-glare diffuser

One warning that saves rework: a shallow cavity does not just need a brighter sheet. It needs a tighter pitch, a stronger diffuser, or both — covered in Step 2.

Step 2 — Measure the Area and the Cavity Depth

Three numbers decide whether the finished panel looks even: total area, cavity depth, and the LED pitch of the sheet you are considering. Measure all three before you order, and measure the usable depth — structure, brackets and cable entries all eat into it.

What to measureWaarom het ertoe doet
Overall width and height of the lit areaSets total coverage and the sheet count; do not measure the frame, measure the visible face
Usable depth from sheet surface to diffuserThis is the mixing distance — the single biggest factor in hotspot control
Diffuser type and thickness (PMMA / PC, 2 / 3 / 5 mm)Sets transmission and haze; a 2 mm clear panel hides nothing
Front material translucencyOnyx glows; painted MDF does not. Verify with a sample before ordering wattage
Power location and cable routeDecides zone splitting and whether you can reach the driver for service
Access panels and fixingsA sealed cavity with no access is a maintenance trap

The most useful rule in backlighting is about geometry, not materials: the distance from the LEDs to the diffuser should be at least equal to the LED pitch, and ideally 1.5–2.5 times the pitch. Below that, individual chips punch through no matter how good the diffuser is.

LED pitch on the sheetMinimum mixing distanceComfortable distance
10 mm10 mm15 – 25 mm
20 mm20 mm30 – 50 mm
30 mm30 mm45 – 75 mm

Around 20 mm spacing is a practical reference for shallow backlit cabinets, but treat it as a starting point rather than a rule — beam angle, diffuser haze and the front material all shift the result. In the display industry the same relationship is tracked as an A/P ratio (distance to active area versus LED pitch), with A/P ≥ 0.8 treated as controllable. For thin translucent stone only a few millimetres thick, keep at least 50 mm of spacing to the surface or you will see the chips through the veining.

Also plan the perimeter. Gaps at the edge of a sheet read as a dark frame line, so either run the sheet close to the edge with a reflective liner, or accept a deliberate border and design it in.

Step 3 — Choose Modular, Long-Roll or Cut-to-Shape

Sheets come in three practical formats. The choice is mostly about geometry: how regular the surface is, and how many connections you are willing to make.

FormatTypical sizeSnijdenConnectionsBeste voor
Modular sheets250 × 250 mm up to 480 × 240 mmOn the grid, in 1 / 3 / 6-light modulesDaisy-chain quick connectorsGrid layouts, cabinets, small or broken-up areas
Long-roll sheets240 mm wide, up to 10 m per rollAt marked intervals onlyScrew terminals, no solderingLarge flat uninterrupted surfaces, lightboxes
Cut-to-shapeCustom outline per drawingFollows the contour, soldered jointsSoldered or custom harnessIrregular stone, curved returns, corner cut-outs

Option A — modular grid (4 × 4 = 16 sheets)

Even coverage, many small connection points.

sheet
sheet
sheet
sheet
sheet
sheet
sheet
sheet
sheet
sheet
sheet
sheet
sheet
sheet
sheet
sheet

Option B — long-roll bands (4 runs × 2 m)

Fewer joints, better voltage stability, cleaner surface.

2 m run
2 m run
2 m run
2 m run

Rule of thumb: if the surface is regular and wider than about 1 m in both directions, long-roll wins on joints and voltage stability. If there are corners, cut-outs or structural returns, modular or cut-to-shape keeps the light close to the edge. For a shallow niche, small modular sheets beat a big one simply because you can fit them.

Step 4 — Calculate How Many Sheets You Need

Worked example used throughout this guide: a backlit kitchen island panel, 1830 × 915 mm (72 × 36 in), 50 mm cavity, onyx front.

Option A — 480 × 240 mm sheets

1830 ÷ 480 = 3.8 → 4 sheets across

915 ÷ 240 = 3.8 → 4 rows

4 × 4 = 16 sheets

16 × 45 W = 720 W total load

Option B — 240 mm × 2 m rolls

915 ÷ 240 = 3.8 → 4 bands

Each band covers 1.83 m

4 × 2 m = 8 m of sheet

4 × 96 W = 384 W total load

Always round up, then add margin for edge trim and mistakes: 10–15% extra sheet area is normal on a first build, less on repeat production. If you cut, count the cut lines rather than the area — a sheet cut into 3-light modules cannot then be cut into 1-light modules, so plan the module size once.

Note the power difference between the two options for the same surface: 720 W versus 384 W. Option A uses denser, brighter sheets; Option B uses fewer, longer runs at lower wattage. Neither is “better” — one is brighter and easier to service, the other has fewer joints and less load on the driver.

Step 5 — Size the Driver and Split the Load into Zones

Power is where most flickering and dim-end problems start. Do the arithmetic before you buy: total load, safety margin, driver count, then zones.

ItemOption A (16 sheets)Option B (4 × 2 m rolls)
Connected load720 W384 W
Recommended margin (20–30%)864 – 936 W460 – 500 W
Typical driver choice1 × 1000 W 24 V, or 2 × 500 W1 × 500 W 24 V
Controllers needed2 for dimming at this load1
Z1

Zone the load

Treat every 300–400 W as a zone with its own driver output and return. If one zone dims, you can find it without opening the whole panel.

Z2

Keep runs short

Long DC cable adds resistance. Feed each zone from its own output rather than daisy-chaining 20 m of 24 V cable.

Z3

Match the control

Tunable white needs a two-channel driver. Addressable sheets need their own protocol — never mix them with standard dimming sheets on one controller.

Headroom is not optional. An undersized driver shows up first as flicker at low dim levels, then as a shortened life. If your total lands near a driver rating, step up a size rather than running at 95%.

For long 24 V runs, check the actual drop before installation with our LED voltage drop calculator. A 1 V drop at the end of a run is visible as a dim band on a backlit surface, even when the driver is correctly sized.

Step 6 — Wire, Mount and Respect Series Limits

Both formats follow the same mounting logic: a clean, flat surface, high-adhesion backing for alignment, and mechanical fixings wherever the panel will be serviced or where heat builds up.

LimitModular sheetsLong-roll sheets
Maximum per series runAbout 5 sheetsUp to 10 m continuous
Connector current capacity5 – 6 AAbout 10 A
What happens past the limitVoltage drop, dim end of run, heat at the connectorFade along the last metres, warm connector

Wiring discipline that prevents most callbacks: keep polarity consistent between sheet and driver, keep AC and DC separated, gland the entry point, and fuse the DC side. In wet or outdoor locations the sheet itself is not the waterproof element — seal the cavity, use an IP-rated diffuser assembly, and keep the driver in a dry enclosure.

If the same project also has straight runs along the panel edge, our drywall LED channel guide en de flexible aluminum channel guide cover the linear side of the build.

Step 7 — Dry-Fit Before You Close the Panel

This is the step almost everyone skips, and the one that catches the expensive problems. Test the optical stack before the panel is sealed.

01

Mount temporarily

Lay the sheets in position without final fixings. Route the cables as they will actually run.

02

Power every zone

Switch on zone by zone. A zone that is visibly dimmer than its neighbour is a wiring or load problem, not an optics problem.

03

Put the real front material on

Place the actual onyx, acrylic or diffuser. Never judge uniformity from bare LEDs.

04

Inspect at viewing distance

Stand where the client will stand. Check centre, edges, seams and the areas around power feeds, then photograph at a fixed exposure.

Set a target before you look: a brightest-to-darkest ratio of about 8:1 or tighter reads as smooth on a backlit surface. If you can see chips at normal viewing distance, do not add more LEDs first — fix distance, diffuser or sheet spacing, in that order.

Record the pass: photograph with the same exposure and settings, and keep the approved sample. It becomes the reference for the rest of the production run, and it settles arguments later far faster than opinions.

Common Mistakes Behind Hotspots and Dark Patches

Almost every uneven backlit panel traces back to one of these. Diagnose by the shape of the fault before changing components.

SymptoomMost likely causeRepareren
Visible rows of dotsMixing distance shorter than the LED pitchIncrease cavity depth, tighten pitch, or move to a higher-haze diffuser
Dark band at a seamSheets spaced too far apart, light fields do not overlapClose the gap or add a bridging cut section
One end of a run is dimmerVoltage drop, series run over the limitShorten the run, inject power at both ends, split the zone
Warm or pink tint toward one endVoltage drop plus bin/colour shift between sheetsKeep one bin per panel, split zones, feed from both ends
Bright frame line around the edgeStructural shadow or reflective liner ending shortExtend the liner, run the sheet closer to the edge, mask the transition
Flicker at low dim levelsDriver near its rating, or controller mismatchStep up the driver size, confirm protocol compatibility
Panel dims over monthsHeat build-up in a sealed cavityVentilate the cavity, derate the load, use thermal tape and fixings

Two more habits prevent trouble: cut only at the marked cut lines (a wrong cut severs a circuit and cannot be repaired), and store sheets dry — humidity oxidises soldered joints and shows up later as an intermittent dim section.

Where LED Sheet Backlighting Works Best

The format wins wherever a surface needs to glow rather than be lit from outside. These are the applications that come up most often in project enquiries.

Backlit stone bar counter lit by LED sheets

Stone bar counters

Onyx and marble counters glow from within; the sheet follows the counter outline so the light reaches the returns, not just the centre.

Alabaster feature wall backlit by LED sheet panels

Feature walls

Alabaster and thin stone walls read as luminous panels when the sheet sits 50 mm or more behind the face.

Backlit headboard with warm LED sheet light

Headboards and fabric panels

Fabric diffuses beautifully. Warm 2700–3000 K here, with the sheet kept well below eye level glare.

Display case backlighting with LED sheet

Display cases and niches

Shallow niches suit small modular sheets; coverage close to the edge is what makes a product look framed.

Retail display backlighting with LED lighting

Retail and POS displays

Even luminance keeps product colour honest — uneven panels shift perceived colour as much as they look cheap.

One caution for stone projects: veining and thickness variation change the transmission, so a visually darker patch may be the material, not the lighting. Test with the actual slab before you change the electrical design.

KayTai Sheet Panels and Matching Profiles

KayTai supplies cuttable LED sheet panels and the profiles for the linear edges of the same project. Both are available with custom size, CCT, CRI and voltage on project orders.

Tunable white LED sheet panel 250 x 250 mm

Tunable White LED Sheet Panel 250 × 250 mm

72 × 2835, 24 V, 14.4 W, CRI 90, 3000–6000 K tunable — a modular tile for shallow backlit cavities.

Related ranges

For the linear edges of the same panel, or for tunable-white accents around it:

Afstembare witte LED-strips — two-channel CCT control

LED-aluminium profielen — recessed, surface and corner channels

Drywall channel installation guide

LED Sheet Backlighting FAQ

▶How many LED sheets do I need for my backlit panel?

Divide the lit width by the sheet width and the lit height by the sheet height, round both up, then multiply. A 1830 × 915 mm panel with 480 × 240 mm sheets needs 4 × 4 = 16 sheets. Add 10–15% for edge trim on a first build.

▶How far should the LED sheet be from the diffuser?

At least the LED pitch, and preferably 1.5–2.5 times the pitch. With 20 mm spacing, plan 30–50 mm of usable cavity depth; for thin translucent stone keep at least 50 mm to avoid visible chips.

▶Can I cut an LED sheet panel?

Yes, but only on the marked cut lines, usually in 1-light, 3-light or 6-light modules. A cut through a circuit cannot be repaired, so plan the module size before you start.

▶Is an LED sheet better than an LED strip for backlighting?

For an area, yes: the sheet covers the surface and hides behind a diffuser. For a linear run — cove, under-cabinet, skirting — a strip in a profile is cheaper, easier to service and better at throwing light along a line.

▶What power supply does an LED sheet system need?

A 24 V constant-voltage driver sized at 1.2–1.3 times the connected load, split into zones of roughly 300–400 W. Use a two-channel driver if the sheets are tunable white.

▶Why does my backlit panel look uneven?

In order of likelihood: mixing distance shorter than the LED pitch, sheets spaced too far apart at seams, voltage drop at the end of a long run, a diffuser with too little haze, or the front material itself varying in thickness and transmission.

▶Can LED sheets be dimmed or colour-tuned?

Yes, with a matching driver and controller. Tunable white sheets need a two-channel driver and a controller that supports CCT; addressable sheets need their own protocol and cannot share a controller with standard dimming sheets.

▶Are LED sheets suitable for bathrooms or outdoor use?

The sheet is low-voltage but not waterproof by itself. Seal the cavity, use an IP-rated diffuser assembly and keep the driver in a dry enclosure. For exposed outdoor surfaces, an IP65+ strip or a sealed panel assembly is the safer route.

Have a Backlit Panel to Specify?

Send us the lit dimensions, cavity depth and front material. Our engineers will come back with a sheet layout, driver sizing and a sample for dry-fit testing.

Neem contact op met KayTai

Laat een reactie achter